Quality Assurance (QA) Craftsman Practice Test

These questions are part of the practice quiz. Start practicing

• Which benefit is most associated with conducting retrospectives in Agile QA?
• What characterizes black-box testing?
• In fastener inspection, what is a major defect?
• In the context of torque, what is meant by 'measured during the assembly phase'?
• What is the difference between "pause work" and "stop work"?
• Define "load testing".
• Which is NOT one of the most common Levels of Essentiality (LOEs)?
• QA Form 26 is used for which type of test record?
• What does Final Torque refer to in the context of fastening?
• Which QA Form serves as a supplement to the Maintenance Certification Record?
• What is an alternative name for Running Torque?
• Which form is utilized for documenting a Shop Test?
• What is exploratory testing?
• Which type of controlled work is focused on nuclear evaluations?
• What defines an SOSMIL maintenance item?
• What does the term "retrospective" refer to in Agile QA processes?
• What process is used for exceptions to retest requirements for mechanical joints?
• What does a yellow label/tag signify on a device?
• What pressure is used for the H-Pressure strength and porosity test?
• What does the ball and seat stack height indicate?
• What is the purpose of "compatibility testing"?
• QA Form 14 is associated with which type of record?
• What does SOSMIL stand for?
• Who must authorize SOSMIL operations?
• What are the discrete SUBSAFE boundary groups?
• What is load testing primarily concerned with?
• Why is it important to validate test assumptions?
• What does "test data management" involve?
• What is the purpose of the document related to Controlled Assemblies?
• What color label is used to denote a device is inactive and removed from the calibration cycle?
• What is typically included in a Formal Work Package (FWP)?
• Which record can be utilized for both torque and assembly documentation?
• How is a Minor DFS defined?
• What is the minimum soak time for the H-Pressure test?
• What does risk-based testing prioritize?
• What is a "test case" in QA?
• What does WAF stand for in a work authorization context?
• QA Form 17SI is used for documenting which of the following?
• What document format is primarily used to correct a technical error?
• What is the purpose of the J-Pressure joint tightness test?
• Which aspect is primary when determining test coverage?
• Which maintenance operation requires special attention under SOSMIL?
• QA Form 34A is used for which of the following records?
• What ensures that all parties are well informed before commencing work?
• What does rework indicate in a QA process?
• What role do automated builds play in continuous integration?
• What type of testing is categorized as shop testing?
• In Agile QA, what is a common outcome of a retrospective meeting?
• Which of the following should be scheduled on the SOSMIL?
• What color is the label used to indicate a device requires no calibration?
• When is an Attachment used in the context of an FWP?
• What is the aim of integration testing?
• What is meant by test case prioritization?
• Which Margin Symbol is used for steps that need authorization?
• What is the main purpose of configuration management in QA?
• Which QA form is used to record welding in progress control?
• What type of measurement does QA Form 35 document?
• What are the three types of Technical Work Documents (TWDs)?
• What situation warrants a voiding process?
• Which type of testing verifies that software functions according to specified requirements?
• What does a "Calibration Void" label signify?
• Who must approve the Rework Addendum?
• Which of the following is NOT a duty of FMA craftsmen?
• What does the QA Form 17 represent?
• What is the purpose of performance testing in QA?
• What is an acceptable condition for minor defects in fasteners?
• What does the term "pause work" imply?
• Which QA Form would you use to verify the results of a Drop Test?
• What information is required to perform any work using MP?
• What is the purpose of the QA Form 11?
• What situation would require a revision to a Controlled Work Package (CWP)?
• What does the Margin Symbol "R" indicate?
• What is the primary goal of Quality Assurance (QA)?
• What is the definition of torque measured in ft/lbs and in/lbs?
• What does regression testing typically aim to ensure?
• What aspect is essential for Controlled Material verification and regulation?
• What is a "bug report"?
• What does OQE signify in quality assurance practices?
• What is the essence of test-driven development (TDD)?
• Why is defining acceptance criteria important in QA?
• What is the primary focus of QA Form 27?
• Which QA form is designated for recording ultrasonic inspections?
• What does the term "defect lifecycle" refer to?
• What does the Margin Symbol "CI" indicate?
• Which incident is associated with the creation of the SUBSAFE program?
• For which of the following purposes would one use QA Form 28?
• What is Required Torque?
• Which factor is critical during the drop test procedure?
• Who can assign a Q-point within a package?
• What is a characteristic of MP (Maintenance Procedures)?
• What is the primary purpose of a Supplement in QA documentation?
• What is an incident report in QA?
• Which of the following types of controlled work is NOT explicitly mentioned?
• What is the purpose of the Pre-Shift Brief?
• What defines a "checklist" in Quality Assurance (QA)?
• What type of record is associated with QA Form 27?
• What does QA Form 9 document?
• How is "defect density" calculated?
• Which QA form is concerned with the inspection of weld defects?
• What is "security testing"?
• What type of records does QA Form 18A encompass?
• What is the range of sizes for self-locking fasteners that Running Torque is applicable to?
• What does "regression testing" involve?
• What is the purpose of load testing tooling?
• QA Form 17B is specifically used for which type of repairs?
• What must a non-technical change in an FWP include?
• What approach is best for improving "test coverage"?
• Which QA form includes records of pipe, machinery, and pressure vessel welds?
• Which statement best describes automated testing?
• What does the Margin Symbol "I" represent?
• What must be confirmed about TMDE before use?
• When should QA Form 26 be used?
• Who is responsible for signing the WAF?
• Which level of testing evaluates the entire system's compliance with specified requirements?
• Which of the following is NOT a method for making changes on FWPs/CWPs?
• What three components make up Controlled Work Packages (CWP)?
• What purpose does the QA Form 17C serve?
• What type of testing assesses the usability of a software application?
• Remarking the assembly of components is documented in which QA form?
• What is emphasized during the Pre-Job Brief?
• Continuous integration primarily aims to reduce what type of risk?
• What is the purpose of QA Form 2?
• Which characteristic best describes a good test case?
• Which form should be referenced for torque and assembly information?
• What is the fundamental rule of all maintenance?
• What is "smoke testing"?
• Which torque value is required to continue turning a self-locking fastener prior to contact?
• What is the primary focus of boundary value analysis?
• Which tool is commonly used for defect tracking in QA processes?
• How is torque defined in terms of measurement?
• Which record is NOT included in QA Form 17?
• What is one of the primary functions of WAFs?
• What does DFS stand for in a Quality Assurance context?
• Why is documentation of rework important?
• What event highlighted the danger of O-ring failure in spacecraft?
• What is a performance benchmark?
• What is a "test closure report"?
• What does "static testing" involve in QA?
• Which QA form is used for recording the assembly of components?
• What action is required when a rework is identified?
• What is the primary function of a drop test?
• Which QA form specifically tracks weld history?
• What is the maximum allowable range for analog test gauges according to the provided standards?
• What does "test automation" refer to?
• Which of the following accurately describes a revision in Quality Assurance?
• What does the QA Form 12 specifically address?
• What must be provided when rework is necessary due to errors?
• Which record is critical for documenting the access, removal and installation of submarine flight components?
• The Submarine Flight Critical Component Record is documented in which form?
• What is the purpose of a test environment?
• Tests that validate "test assumptions" are typically conducted to ensure what?
• Which of the following materials is categorized as Nuclear Level 1?
• What is the required approval for technical changes in work packages?
• What does "mobile testing" involve?
• Which QA form is utilized for documenting Discrepancies during audits?
• What was the cause of the USS Iwo Jima incident?
• What does non-functional testing assess in a system?
• QA Form 35 mainly focuses on the measurement of what?
• What is the definition of "stop work"?
• What distinguishes Quality Assurance from Quality Control?
• What is NOT a requirement of a Rework Addendum?
• What does a "Calibrated" label indicate for a device?
• Which quality assurance record deals specifically with the results of a Shop Test?
• Under what condition might the scope of work change in a CWP?
• What is a "test execution log"?
• What is the purpose of a "test readiness review"?
• What does the "G" margin symbol signify?
• Who prepares the SOSMIL document?
• Which document confirms the structural integrity of welds and their history?
• What is the submission purpose of QA Form 20A?
• Why is documentation important in QA processes?
• What best defines "continuous integration" in software development?
• Which form is specifically related to radiographic test inspections?
• What is the definition of SUBSAFE?
• What qualifies as a Major DFS?
• Which form is specifically used for recording Controlled Assembly Exceptions?
• What is the primary purpose of Controlled Work Packages (CWP)?
• What does LOE stand for in the context of quality assurance?
• Which form is used as a handling equipment test record?
• What does the Margin Symbol "S" denote?
• What is NOT a potential SOSMIL maintenance activity?
• What aspect does QA Form 10 supplement in quality assurance processes?
• What is recorded in QA Form 12A?
• What is the purpose of performance testing in QA?
• When is SOSMIL prepared?
• What type of record is QA Form 1?
• In software development, what does the acronym "SDLC" stand for?
• What is one of the main goals of conducting retrospectives in Agile?
• What is the purpose of QA Form 20C?
• In the context of FWPs/CWPs, which method is appropriate for making minor administrative changes?
• What is the difference between non-technical and technical changes in work packages?
• In quality assurance documentation, what is a 'Controlled Material Reject Tag' used for?
• Why is it important to select a test pressure properly for analog gauges?
• What is a "test plan"?
• What does TMDE stand for?
• Why are test metrics significant in Quality Assurance?
• What does QA Form 34 document?
• Which of the following describes hull integrity fasteners?
• Which QA Form is used for a controlled material reject tag?
• What does QA Form 20B (Part A) specifically document?
• Which of the following is NOT identified by a calibration label?
• What is chaos testing designed to do?
• The concept of "test coverage" is crucial because it helps to:
• What do code reviews help achieve in QA?
• When selecting torque wrenches, what is the recommended final torque range?
• What does QA Form 20B (Part B) document?
• What does the Margin Symbol "C" signify?
• How often should tests be run in a continuous integration environment?
• The responsibility for conducting a Pre-Job Brief lies primarily with whom?
• What is indicated by QA Form 34A in quality assurance processes?
• Which method allows for the addition of important information to existing work packages?
• How detailed should FWPs (Formal Work Packages) be?
• What is a minimum requirement that must be included in calibration labels?
• What is the role of a QA engineer in an Agile environment?
• What is the purpose of blue checks in fastener inspection?
• What type of record is maintained under QA Form 17A?
• Which of the following is NOT a component of Controlled Material?
• What is the primary purpose of Q-Points in a Controlled Work Package?
• Which of the following is NOT a type of QA Form 17 repair record?
• What are "test scripts"?
• In the context of software testing, what are "test assumptions"?
• What does 'Controlled Material' refer to?
• What is the maximum allowable test pressure for hydrostatic test gauges?
• What is the focus of white-box testing?
• What is "API testing"?
• What is the purpose of using Margin Symbols in documentation?
• What is meant by "root cause analysis" in QA?
• What is "user acceptance testing (UAT)"?
• What does JFMM stand for?
• What does "test coverage" indicate?
• What does Breakaway Torque refer to?